Rigol DSG3000 Series Dokumentacja Strona 252
- Strona / 262
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
RIGOL
DS6000 User’s Guide
16-4
Negative Slope (greater than, lower than, within specific
interval)
Time Setting
10 ns to 1 s
Video Trigger
Signal Standard
Line Frequency
Range
Support standard NTSC, PAL and SECAM broadcasting
standards, the range of the number of lines is from 1 to 525
(NTSC) and 1 to 625 (PAL/SECAM)
Pattern Trigger
Pattern Setting
H, L, X, Rising Edge, Falling Edge
RS232/UART Trigger
Trigger Condition
Start, Error, Check Error, Data
Baud Rate
2400bps, 4800bps, 9600bps, 19200bps, 38400bps,
57600bps, 115200bps, User
Data Bits
5 bit, 6 bit, 7 bit, 8 bit
I2C Trigger
Trigger Condition
Start, Restart, Stop, Missing ACK, Address, Data, A&D
Address Bits
7 bit, 10 bit
Address Range
0 to 119, 0 to 1023
Byte Length
1 to 5
Data Qualifier
Equal to, Greater than, Less than
SPI Trigger
Trigger Condition
CS, Timeout
Timeout Value
100 ns to 1 s
Data Bits
4 bit to 32 bit
Data Line Setting
H, L, X
Clock Edge
Rising Edge, Falling Edge
Signal Type
Rx, Tx, CAN_H, CAN_L, Differential
CAN Trigger
Trigger Condition
SOF, EOF, Frame Type
Baud Rate
10kbps, 20kbps, 33.3kbps, 50kbps, 62.5kbps, 83.3kbps,
100kbps, 125kbps, 250kbps, 500kbps, 800kbps, 1Mbps,
User
Sample Point
5% to 95%
Frame Type
Data, Remote, Error, OverLoad
USB Trigger
Signal Speed
Low Speed, Full Speed
- User’Guide 1
- Guaranty and Declaration 3
- Safety Requirement 4
- Safety Terms and Symbols 6
- Measurement Category 7
- Ventilation Requirement 8
- Working Environment 9
- DS6000 User’s Guide 10
- General Care and Cleaning 11
- Environmental Considerations 12
- DS6000 Series Overview 13
- Document Overview 15
- Contents 17
- 1 Quick Start 23
- General Inspection 24
- Appearance and Dimensions 25
- To Remove the Cover 26
- To Use the Battery 29
- Power-on Inspection 30
- To Connect the Probe 31
- Function Inspection 32
- Probe Compensation 34
- Front Panel Overview 35
- Rear Panel Overview 36
- VERTICAL 38
- HORIZONTAL 40
- TRIGGER 41
- Run/Stop 41
- Navigation Knob 43
- User Interface 45
- To Use the Security Lock 50
- To Use the Rack Mount Kit 52
- Installation Tool 53
- Installation Space 54
- Installation Procedures 55
- knob ) at the front 58
- 2 To Set the Vertical System 59
- To Enable the Channel 60
- Channel Coupling 61
- Bandwidth Limit 62
- Input Impedance 64
- Waveform Invert 65
- Vertical Scale 65
- Vertical Expansion 66
- Amplitude Unit 66
- Channel Label 67
- Delayed Sweep 70
- Time Base Mode 72
- X-Y Mode 73
- ” on page 6-17 75
- Roll Mode 76
- Horizontal Scale 77
- Horizontal Reference 78
- 79
- 4 To Set the Sample System 81
- Acquisition Mode 82
- Peak Detect 84
- High Resolution 84
- Sample Mode 85
- Sample Rate 86
- Memory Depth 88
- Antialiasing 89
- Trigger Source 92
- Trigger Mode 93
- Trigger Coupling 95
- Trigger Holdoff 96
- Noise Rejection 97
- Trigger Type 98
- Edge Trigger 99
- Pulse Trigger 100
- Slope Trigger 102
- Video Trigger 105
- Pattern Trigger 107
- RS232 Trigger 109
- I2C Trigger 111
- SPI Trigger 113
- CAN Trigger 115
- DS6000 User’s Guide 117
- USB Trigger 118
- Trigger Level: 119
- Trigger Ouput Connector 120
- 6 To Make Measurements 121
- Math Operation 122
- Subtraction 123
- Multiplication 123
- Division 124
- Logic Operation 128
- Advanced Operation 130
- Auto Measurement 133
- Quick Measurement after Auto 134
- Time Parameters 136
- Voltage Parameters 138
- Measurement Setting 141
- Clear the Measurement 143
- All Measurement 144
- Statistic Function 145
- Measurement History 146
- Cursor Measurement 147
- Manual Mode 148
- Track Mode 151
- Auto Mode 154
- 7 Protocol Decoding 155
- Parallel Decoding 156
- Threshold 157
- RS232 Decoding (Option) 158
- Stop Bit 159
- Check Bit 159
- Start Phase 159
- Data Bits 159
- Detect the parity bit is 1 161
- 0x52 (01010010, LSB) 161
- SPI Decoding (Option) 162
- I2C Decoding (Option) 165
- CAN Decoding (Option) 167
- 8 Reference Waveform 169
- To Enable REF Function 170
- To Select REF Source 171
- To Save to Internal Memory 171
- 9 Pass/Fail Test 173
- To Select Source 175
- To Create Mask 175
- Test and Output 175
- To Save the Test Mask 176
- To Load the Test Mask 176
- 10 Waveform Recording 177
- Waveform Recording 178
- Waveform Playback 180
- Waveform Analysis 182
- Analysis Based on Trace 185
- 11 Display Control 187
- To Select the Display Type 188
- To Set the Persistence Time 189
- To Set the Screen Grid 191
- To Set the Grid Brightness 191
- To Set the Menu Display 191
- 12 Store and Recall 193
- Storage System 194
- Storage Type 195
- Internal Store and Recall 197
- External Store and Recall 200
- Disk Management 203
- English Input Method 205
- Chinese Input Method 206
- To Delete a File or Folder 207
- To Rename a File or Folder 207
- To Copy and Paste a File 208
- To Clear the Local Memory 208
- Factory 209
- 13 System Function Setting 215
- LAN Setting 216
- IP Configuration Type (DHCP) 217
- Set the Gate 218
- Set the Domain Name Server 218
- MAC Address 219
- VISA Address 219
- USB Device 220
- To Set the GPIB Address 220
- System-related 221
- Power-off Recall 222
- System Time 222
- Self-calibration Information 224
- Error Information 226
- Self-calibration 227
- Power Status 228
- External Trigger Impedance 228
- Aux Output 229
- Reference Clock 230
- Option Management 231
- To Print the Waveform 232
- Normal Print 233
- PictBridge Print 234
- 14 Remote Control 237
- Remote Control via USB 238
- Remote Control via LAN 242
- Remote Control via GPIB 245
- 15 Troubleshooting 247
- 16 Specifications 249
- Trigger 251
- 17 Appendix 257
- Appendix B: Warranty 258
Powiązane produkty i podręczniki dla Pomiary, testowanie i kontrola Rigol DSG3000 Series
(146 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.028 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji